ฝากข้อความ
เราจะโทรกลับหาคุณเร็ว ๆ นี้!
ข้อความของคุณจะต้องอยู่ระหว่าง 20-3,000 ตัวอักษร!
กรุณาตรวจสอบอีเมลของคุณ!
ข้อมูลเพิ่มเติมช่วยให้การสื่อสารดีขึ้น
ส่งเรียบร้อยแล้ว!
เราจะโทรกลับหาคุณเร็ว ๆ นี้!
ฝากข้อความ
เราจะโทรกลับหาคุณเร็ว ๆ นี้!
ข้อความของคุณจะต้องอยู่ระหว่าง 20-3,000 ตัวอักษร!
กรุณาตรวจสอบอีเมลของคุณ!
—— มิโยะ
—— ออคตาวิโอ
—— คริสเตียน
—— สเปนซ์
—— Samuel
—— อาลี
When the tile press machine is working normally, there will be burrs on the cutting board. เมื่อเครื่องกดกระเบื้องทำงานตามปกติจะมีเสี้ยนบนเขียง This is a frequent failure, so how to solve this problem? นี่คือความล้มเหลวบ่อยครั้งดังนั้นวิธีการแก้ปัญหานี้?
1. First check whether the screws of the slide rail clamps are loose. 1. ตรวจสอบก่อนว่าสกรูของที่ยึดรางเลื่อนหลุดหรือไม่ If loose, tighten them to feel firm and hard. หากหลวมให้กระชับให้แน่นและแข็ง
2. Loosen the oil pressure to a minimum. 2. คลายแรงดันน้ำมันให้น้อยที่สุด Loosen the oil pressure adjustment screw outward. คลายสกรูปรับแรงดันน้ำมันออกด้านนอก
3. Choose manual, jog the knife to drop, make the upper and lower knife overlap about half a centimeter. 3. เลือกแมนนวลแล้วเขย่ามีดเพื่อทำให้มีดบนและล่างซ้อนกันประมาณครึ่งเซนติเมตร If the cutter does not move, adjust the oil pressure appropriately. หากใบมีดไม่เคลื่อนที่ให้ปรับแรงดันน้ำมันอย่างเหมาะสม Loosen the external adjustment screw of the bottom knife, tighten the back adjustment screw, and tighten the external adjustment screw. คลายสกรูปรับภายนอกของมีดล่างขันสกรูปรับหลังให้แน่นแล้วขันสกรูปรับภายนอกให้แน่น Jog the cutter to rise. เขย่าเบา ๆ คัตเตอร์ให้สูงขึ้น If you hear a "bang", it proves that the adjustment is too much or uneven. หากคุณได้ยิน "ปัง" แสดงว่าการปรับค่านั้นมากเกินไปหรือไม่สม่ำเสมอ The bottom knife should be adjusted inwards first, and the upper knife should be dropped and readjusted. ควรปรับใบมีดด้านล่างเข้าด้านในก่อนและควรปรับใบมีดด้านบน After adjustment, first use a small piece of board to test the knife. หลังจากการปรับใช้ครั้งแรกให้ใช้บอร์ดขนาดเล็กเพื่อทดสอบมีด
4. การปรับใบมีดเป็นงานที่ระมัดระวังและต้องใช้ความอดทน