ส่งข้อความ
บ้าน ข่าว

ข่าว บริษัท เกี่ยวกับ Precautions For The Use of Decking Floor Sheet Machine?

ได้รับการรับรอง
ประเทศจีน Cangzhou Best Machinery Co., Ltd รับรอง
ประเทศจีน Cangzhou Best Machinery Co., Ltd รับรอง
ความคิดเห็นของลูกค้า
ฉันมีความสุขกับ Cangzhou BEST Machinery Co.,Ltd. โรงงานที่เป็นมืออาชีพและน่าเชื่อถือมาก พวกเขานำเสนอเครื่องจักรคุณภาพดีและเซิร์ฟเวอร์การขายที่ดี หวังว่าจะได้ร่วมมือกับพวกเขาอีกครั้ง

—— มิโยะ

เครื่องจักรของ Cangzhou BEST Machinery co.,ltd ดีมาก และการผลิตรวดเร็ว จัดส่งรวดเร็ว บริษัท turstfull มาก

—— ออคตาวิโอ

ขอบคุณสำหรับการต้อนรับที่ดีของคุณ บริษัทของคุณเป็นมืออาชีพมาก เราจะมีความร่วมมือที่ดีในอนาคตอันใกล้นี้

—— คริสเตียน

บริษัทที่ดีมากผ่านการสื่อสารที่ดีมาก ปัญหาทั้งหมดได้รับการแก้ไข พอใจกับการซื้อของฉัน

—— สเปนซ์

very professional factory, realiable, happy with them

—— Samuel

บริการดี จัดส่งเร็ว สื่อสารดี

—— อาลี

สนทนาออนไลน์ตอนนี้ฉัน
บริษัท ข่าว
Precautions For The Use of Decking Floor Sheet Machine?
ข่าว บริษัท ล่าสุดเกี่ยวกับ Precautions For The Use of Decking Floor Sheet Machine?

Before the equipment is used, check whether the connections are secure and whether the installation bolts and nuts are tightened. The left and right chassis should be lubricated with lubricating oil to start the machine after power-on. First, run the vehicle and observe carefully, whether there is vibration, noise, oil window Whether oil comes, whether the movement of each part is coordinated, and the mold can only be installed after everything is normal. When installing the mold, you must cut off the power and manually move the motor belt or large gear to index the worktable and raise the slide to the highest point. It is best to use an object to support between the worktable and the bottom surface of the slide, so that the anti-skid seat naturally falls, causing an accident.
The mold used in this machine needs an upper mold and six lower molds of the same size. First install the upper mold and one lower mold. The lower mold is directly installed on the hexagonal runner table, and the upper mold is installed on the bottom surface of the slide, and Place a pad of appropriate thickness to ensure that after the upper and lower molds are closed, the gap between the four sides is uniform, and the distance between the upper and lower molds is equal to the required thickness of the tile blank. Then, based on the upper mold, the worktable is indexed, and the remaining five lower molds are installed. After all the upper and lower molds are installed, the tile can be driven to drive.

ผับเวลา : 2020-04-16 11:10:02 >> รายการข่าว
รายละเอียดการติดต่อ
Cangzhou Best Machinery Co., Ltd

ผู้ติดต่อ: Mr. Arno Hao

โทร: +8618717894416

ส่งคำถามของคุณกับเราโดยตรง (0 / 3000)