The main part of the cold bending forming equipment is the roller. ส่วนหลักของอุปกรณ์ขึ้นรูปเย็นดัดเป็นลูกกลิ้ง The design of the roll is very important, and its design features are as follows: การออกแบบม้วนมีความสำคัญมากและคุณสมบัติการออกแบบมีดังนี้:
1. หลักการของแรงเฉลี่ยของแต่ละอุปกรณ์การขึ้นรูปเย็นดัดแรงเฉลี่ยของลูกกลิ้งการสึกหรอมีความสมดุลและอายุการใช้งานของลูกกลิ้งเพิ่มขึ้น
2. The material used for the roll is to use its wear resistance, but the specific strength and hardness are contradictory. 2. วัสดุที่ใช้สำหรับม้วนคือการใช้ความต้านทานการสึกหรอ แต่ความแข็งแรงและความแข็งจำเพาะนั้นขัดแย้งกัน The red hardness of C12MoV should be used during heat treatment. ความแข็งสีแดงของ C12MoV ควรใช้ในระหว่างการอบชุบ After quenching, the hardness can be achieved by two to three tempers. หลังจากชุบแข็งแล้วความแข็งสามารถทำได้สองถึงสามอุณหภูมิ
3. The arc part of the track is the main part of the cold bending forming equipment. 3. ส่วนโค้งของแทร็กเป็นส่วนหลักของอุปกรณ์ขึ้นรูปเย็นดัด The arc position after the first few press forming, when the vertical edge is rolled in the subsequent pass, the formed arc should be protected by the upper and lower rolls or the horizontal wheel. ตำแหน่งส่วนโค้งหลังจากกดสองสามครั้งแรกเมื่อขอบแนวตั้งถูกรีดในการผ่านครั้งต่อไปส่วนโค้งที่เกิดขึ้นควรได้รับการปกป้องโดยม้วนบนและล่างหรือล้อแนวนอน Tube bundle. หลอดมัด Otherwise, the arc position of the material will change during the stretching process, R becomes smaller and becomes triangle, and when the shape R becomes larger, the matching rail will sway, uneven stress, the rail will be deformed, and the service life will be reduced. ไม่เช่นนั้นตำแหน่งอาร์คของวัสดุจะเปลี่ยนไปในระหว่างกระบวนการยืด, R จะเล็กลงและกลายเป็นรูปสามเหลี่ยมและเมื่อรูปร่าง R ใหญ่ขึ้นราวจับคู่จะสั่นไหวความเครียดไม่สม่ำเสมอรางจะเสียรูปและอายุการใช้งานจะ จะลดลง
4. Rolling stability problem, the problem of deflection of the material in the raceway is often encountered during production. 4. ปัญหาความมั่นคงในการกลิ้งปัญหาการโก่งตัวของวัสดุในร่องน้ำมักเกิดขึ้นระหว่างการผลิต In fact, a single set of rollers is asymmetric, the left side is stressed, and the material deflects to the right; ในความเป็นจริงลูกกลิ้งชุดเดียวไม่สมมาตรด้านซ้ายเน้นและวัสดุเบี่ยงไปทางขวา the right side is stressed, the material Swing to the left ด้านขวาจะเน้นวัสดุที่แกว่งไปทางซ้าย
ผู้ติดต่อ: Mr. Arno Hao
โทร: +8618717894416